Duotone Wing Set – Aero Carve 2.0 D/LAB

£745.00£1,160.00

Description

PERFORMANCE SURF / FREESTYLE / PRONE / KITE

Our most advanced front wings to date! In search of reducing the drag and weight of our foils to a minimum, we decided to merge the front wing and front half of the fuselage together. This eliminates any compromise in terms of shaping the front wing to fit our fuselage front wing mount. It also allows us to remove the three bolts which are necessary to fix our “bolt on” SLS front wings on our fuselages, reducing the drag and weight even more.

The Carve 2.0 D/LAB, same as the SLS variant, are quite different to our previous Carve range. They feel a lot less draggy and way looser in terms of roll, allowing the rider to do heel side to toe side turns way more naturally. The top end speed has also been increased thanks to a thinner profile towards the wing tips and the higher aspect ratio allows the Carve 2.0 D/LAB to glide and pump much better than its predecessor.

The Carve 2.0 D/LAB range is based on our new Carve 2.0 SLS range but with a few little tweaks. Compared to the SLS range, the aspect ratio is slightly lower and the profile a bit thinner and faster, to allow these wings to be pushed to higher speeds, whether it is going down fast waves, throwing the most technical Freestyle tricks or even using them for Wing Foil or Kite Foil racing.

The D/LAB range also introduces two smaller sizes, the 650 and 500, but doesn’t include the bigger 1430 found in the SLS range. Two carbon tail options in 37cm and 43cm – respectively matching the lengths of our 60cm and 66cm AL 3BS fuselages – complete the D/LAB glider for either a loose and playful character, or higher control at top speeds.

If you want the ultimate performance, the Carve 2.0 D/LAB is the choice for any advanced to top level riders!

Fuselage Aero Tail is not included – please order separately!

FAST AND EASY
Fast and minimal drag – optimized for each individual size
LIGHTWEIGHT
Lowest weight for high performance riding and jumps
HANDLING
Immediate response for intuitive surfing and maximum pop for freestyle
IMPROVEMENT
Improved pump & glide over previous Carve range
SIZE SPECIFIC
Gradually increased control on small sizes and playfulness on larger sizes

SPECIFIC SIZE INFORMATION

500

Our smallest and most radical front wings. The Aero Carve 2.0 D/LAB 500 is targeted to kids/light riders or experienced ones wanting to tackle big fast waves on their wings or kitefoil at Mach 2 speeds. Tweaked to maintain a good level of control when going full speed when paired with the 43cm tail, or to be super turny when used with the 37cm tail. Ideally paired with the 165 P stabilizer and +0.3 deg shim.

650

The second smallest wing in our range, targeted to kids/lighter riders or experienced ones looking for extra speed, whether it is to tackle bigger waves, freestyle on the wing or challenge your friends on a kitefoil race. Rig it with 37 tail for maximum manoeuvrability in the waves or pick the 43 tail for more control at high speed. Ideally paired with the 165 P stabilizer and +0.3 deg shim.

850

The Aero Carve 2.0 D/LAB 850 has it all – it’s got instant turning and response in the waves, exciting speeds for both winging and kite foiling, incredible pop for Freestyle and the glide and low drag efficiency to make it through flat sections. This is the one wing to have in your quiver!

1100

The biggest wing in our D/Lab family. Advanced riders will choose this wing for waveriding in small to medium waves and freestylers will love it in light to medium wind conditions. Best suited to heavy kitefoilers or very light conditions, the 1100 D/Lab is a great allrounder that feels slippery for it size and easy to use. It can also be used for prone surfing, where its turning ability is only matched by the smaller Carve 2.0’s, although realistically it will not pump as well as our other higher aspect front wings.

Fuselage Aero Tail D/LAB – please order separately

Our D/Lab carbon tails are the rear part of the fuselage which fit onto our new Carve 2.0 D/LAB front wings.

Once connected by the “invisible” M6 bolt, they could fool you into thinking that our glider was actually one single carbon part. The unique trick is our clever design which hides under the mast, the bolt used to connect the tail part with the front wing. By doing this, we are able to eliminate the traditional extra bolt heads which are exposed on all our competitor’s foils with similar semi glider concepts.

The D/Lab tails are available in two lengths. A shorter 37cm piece, which once connected to a front wing is the equivalent of our 60cm fuselage, and a longer 43cm piece, which matches the 66cm fuselage.

Pick the 37 tail for a more exciting ride and the possibility to draw tighter turns or settle for the 43 tail for more control at high speeds.

The carbon construction of the D/Lab tails not only guarantees a hassle-free maintenance, but the strong connection to the front wing via two M8 plus one M6 bolt ensures that the complete assembly is as stiff as a single part glider, such as the ones found on our Daytona foils.

Additional information

Wing Size

850/180cm, 1100/200cm, 500/165cm, 650/165cm

Fuse Size

37cm, 43cm, None



Exclusive products

Special category of products